Gneiss House

Low-pressure home metamorphism


Update: Baseboard molding

I never posted about my other winter project: installing base shoe molding throughout the house! So here is a quick overview:

The previous owners had ripped out (in some cases, apparently violently) the baseboard shoe molding through the entire house. This did make it relatively easy to refinish the floors, because there was a little border around the edges of all the rooms where the floor did not have to look perfect. But I did eventually need to replace that molding for a finished look that did not include big gaps under my walls.

I ended up deciding that I do not need to be a pure DIYer: painting 300′ of molding by hand would have taken me forever and barely saved me any money. So I bought prepainted base shoe molding at Home Depot. The price was reasonable and that meant all I had to do was measure it, cut it, and install it in the house.

Measuring: I started with a measuring tape and writing things down on a piece of paper, but ended up just lining up the molding around the whole house and marking it with a pencil. Easier to keep track of where all the pieces had to go, and very easy to mark them correctly that way.

Cutting: I did not have a miter box, and when I borrowed one from my parents, I discovered that it was very difficult to anchor the box firmly enough to use it properly (since it wasn’t mine to install anywhere permanently). I did not at this point have the workbench constructed, so I did the next best thing: mount my little portable table vise to my dining room table (with padding to prevent scratches), cover the surrounding area with newsprint, and go to town with a hacksaw. I lined up a protractor with the pieces that needed to be cut on an angle (like in the corners) and carefully marked the angles, and tried (with reasonable success) to keep the hacksaw on those marks. I was able to cut all the molding for the whole house in two nights.

Installing: I rented a nail gun from Home Depot. Nail guns are really fun for humans, but they terrify dogs, so maybe wait for a nice day and put the dog outside while you do this. Overall this was really, really easy, but 1) use a knee pad, and 2) it is a little tricky if the baseboard molding behind the shoe molding isn’t flush with the floor, such that you are nailing into a gap. It takes some practice to angle the gun correctly to nail the shoe molding in that circumstance.

When I have a chance to refinish the replacement floorboards, I’ll have to do this again for the few areas that need those floorboards (I couldn’t install the molding without floorboards). More fun with nail guns in my future!

Advertisements


Spring #2

Spring has sprung, and with it yard work! I have been working to get the yard ready for spring, take notes on what I want to change or add for next year, and begin the planting and yardwork seasons.

First, I ordered my seeds over the winter, and got everything in the ground that should go in before the last hard frost (peas, one strawberry plant, cauliflower, onions, carrots), and since we had a few warm days in a row in mid-March, I transplanted the hardy parsley and cilantro that made it through the winter to new areas. Then while I waited for the last frost, I started removing obvious weeds from the yard, cleaned up sticks that fell in the recent winter storms, and accumulated tools and replacements, like new work gloves.

Early April was warm unseasonably early, which was refreshing after such a cold March and delayed spring flowering. Once we were clearly safely past the last frost, a little before mid-April, I planted the post-frost seeds (the other herbs except for basil, an extensive oversow of my alternative lawn mix with some viola seeds added in, and a few other flowers to try out) and trimmed the rose bushes (FINALLY, I can walk around them without getting stuck with thorns!). We had some heavy rain right after I sowed, so while I’m concerned that some areas may have washed out a little, overall the cool nights plus rainy weather seems to have forced germination within just a few days.

The spring report so far: my magnolia tree was, as always, a sight to behold:

Image

And the other early spring flowers, most of which were planted by the previous homeowner, came in nicely, if a big sparse. I now know that I will want to fill in the yard substantially this fall with early spring bulbs, to really bring out that show.

Image

The ground is still pretty bare, but we’re starting to see some flowers–the forsythia looked beautiful this year. (Dog for scale.)


2 Comments

Refinishing tables

First, apologies for the long hiatus. Spring is always a very busy time at my job, so I fell behind on both house projects and updates! A lot of the up and coming projects require some ventilation, too, so they had to wait for spring weather. But I’ve had this one in the queue for a while and finally finished the project, so now I can finish writing it up for you!

Backstory: I acquired my dining room table for cheap from craigslist about five years ago. It’s a heavy, cherry dining table (with two leaves!) in a classic, elegant design. Soon after purchasing and precariously driving it home tied to the roof of my parents’ car, we repaired a dog-chewed table leg foot (my dad used wood putty to reform the foot and then stained it to match the table) and rewaxed the top surface. I also scrubbed it with a nice polishing wood cleaner several times over and successfully drew out any cigarette odors remaining in the wood from the previous owners. (Really, owners of wood furniture, do you have to smoke indoors? And then resell your furniture?)

Image

The dining set, in my old apartment immediately after I bought it.

Anyway, the furniture wax polish never seemed to do a great job: wet rings from bottles and glasses, hot items placed on cork trivets or cloth placemats, spilled liquids, warm cat prints, and cat claw scratches all seemed to go right through the wax and damage the finish. I was thinking of rewaxing it again someday soon, but the timeline was accelerated when I spilled half a bowl of near-boiling chicken soup through and under a plastic placemat and created a big white rectangle in the finish.

Image

One side of the table, with assorted moisture stains and rings. Some of the rings predate my ownership of the table.

Image

The newest chicken soup stain, with some older white stains and scratches.

I didn’t entirely understand what was going on at first, so I initially tried stripping the wax with various products: a white vinegar solution, 409 surface cleaner plus a serious scrubbing with a scrubby dish sponge, a commercial wax remover with mineral spirits. The 409 did the best job of removing all the existing wax from past polishing coats, but it did not remove the scratches or white rings/spots/(rectangular placemat shapes). Further research revealed that the wax wasn’t the culprit (though stripping it was not a bad idea): the underlying finish was old and no longer performing its job, so the damage was to the finish itself.

My research had showed that I needed a restoring oil product and ultra fine steel wool. Unfortunately my local hardware store was out of the shade I wanted for the refinishing oil, so I did some dry removal of the damaged finish with the steel wool while I waited for my internet order to arrive (note: it was cheaper to order the refinisher online, anyway!). The dry sanding revealed that the finish was indeed extremely old and damaged: once exposed, I could clearly see hairline cracks throughout the finish. I was able to remove most of the damaged/stained white marks.

Image

Dry sanding scratches and white stain marks. Action shot!

Image

Same area, rotated and after sanding out the stain (but not the scratches). It’s gone!

Image

The whole table after dry sanding. The chicken soup stain was on the front right side. (Note that this picture was taken in the evening, with just artificial light and the shades closed. That is why the lighting looks yellower.)

The product I had ordered was Restor-A-Finish, in cherry (the walnut was not warm enough and a little too dark, but the cherry was probably a smidge too red. This did not end up mattering). Once it arrived, I had to wait for a warm enough day to have the windows open for several hours while doing this job, because this is an oil-based, fumy product that is not safe to breathe in enclosed spaces. But it is worth the fumes. I went back with the steel wool and gently worked the refinishing oil into the whole table, first working in a circular motion with particular focus on visibly damaged areas, and then working in the direction of the wood grain over the whole table to restore the entire finish. I then went back over with dry, lint-free disposable rags and worked the oil into the table and wiped it clean. Then I left the fan on and windows open and took a nice long nap.

After my nap, the table was fully dry (and looked excellent!). The instructions on the refinishing product said to wait half an hour before adding a wax polish, and I ultimately waited an hour or two before starting the waxing step. I used basic old furniture polishing wax, nothing fancy. I put a little bit of the wax in a microwave-safe bowl and microwaved it for five seconds at a time until it was just slightly warmed and softened (but not melted, not even a little. I recommend being careful doing this: waxes are flammable and should never be overheated. It also would not work very well for waxing furniture if it was fully melted!). I did this because the temperature was a little chilly with the windows open, so the wax was quite stiff. I am also a petite person, and I figured that a warmer wax would penetrate nooks and crannies and coat the table more evenly without requiring a lot of physical strength. Having waxed this table once before, I do think it was easier to apply this way. For the application, I used a clean, dry paper towel to scoop out a little bit of wax and a time and rubbed it into the table, alternating between circular motions and working it in with the grain. I removed any excess, wiping with the grain of the wood, and then took the dog for a nice long walk around the neighborhood.

When I got back to my stinky house, I started buffing off the excess wax. I don’t have a buffer or buffing attachment for a power tool, so I did this by hand with clean, dry disposable rags. Because of my lack of enormous physical strength, this was the hardest part of the job. Instead of doing one really hard buffing job, I instead came back to the table to keep buffing it incrementally over the course of a couple days, until the rags were coming out clean. I did a final buffing with a cloth fleece rag, which did a great job for the final touch. I touched it up with a polishing cleanser (I like the Method wood cleanser), and voilĂ : a refinished table!

Image

The refinished dining table, with dog for scale. (Note that this picture was taken midday on a sunny day with the shades open, so the lighting is different than in the last picture.)

Image

That chicken soup stained area.